Voron: Difference between revisions
Jump to navigation
Jump to search
(Created page with "This is my info for my Voron v2.4 build<br> This is what I am using for hardware:<br> * BTT SKR 1.4 Turbo (LPC1769) * BTT EXT MOT * BTT SB2209 USB (RP2040) <br> * Followed this guide to install in Debian 12 https://docs.mainsail.xyz/setup/getting-started/manual-setup '''Add pkg-config to install''' sudo service klipper stop * Build for SKR 1.4 Turbo ~/klipper/scripts/flash-sdcard.sh /dev/serial/by-id/usb-Klipper_lpc1769_0D200015871C4AAF52587C5DC52000F5-if00 btt-skr-tu...") |
No edit summary |
||
| (4 intermediate revisions by the same user not shown) | |||
| Line 1: | Line 1: | ||
This is my info for my Voron v2.4 build<br> | This is my info for my Voron v2.4 build<br> | ||
* Generic Bigtreetech github: https://github.com/bigtreetech/ | |||
This is what I am using for hardware:<br> | This is what I am using for hardware:<br> | ||
* BTT SKR 1.4 Turbo (LPC1769) | * BTT SKR 1.4 Turbo (LPC1769) [https://www.hurlster.com/downloads/BTT%20SKR%20V1.4%20Instruction%20Manual.pdf SKR 1.4 Turbo Manual] | ||
* BTT EXT MOT | * BTT EXT MOT [https://www.hurlster.com/downloads/BTT%20EXP-MOT%20V1.0User%20Guide.pdf EXT-MOT Manual] | ||
* BTT SB2209 USB (RP2040) | * 8MM Funssor Hot Bed Cast Alumnium MIC-6 Plate | ||
110/220V Silicone AC heater has a built-in NTC 100K thermistor. | |||
* BTT TFT35 V2.0 [https://www.hurlster.com/downloads/BTT%20TFT35%20V2.0-manual-20200108.pdf TFT35 V2.0 Manual] | |||
* BTT SB2209 USB (RP2040) [https://www.hurlster.com/downloads/BIGTREETECH%20EBB%20SB2209%20USB%20V1.2%20User%20Manual.pdf EBB Manual] | |||
DC12V-DC24V 9A | |||
Temperature Sensor Interface | |||
1x 100K NTC (pull-up resistor is 2.2K), supports PT1000 | |||
<br> | <br> | ||
* Followed this guide to install in Debian 12 | * Followed this guide to install in Debian 12 | ||
| Line 10: | Line 17: | ||
sudo service klipper stop | sudo service klipper stop | ||
* Build for SKR 1.4 Turbo | * Build for SKR 1.4 Turbo | ||
make menuconfig | |||
--> lp1769 & 120hz | |||
make | |||
~/klipper/scripts/flash-sdcard.sh /dev/serial/by-id/usb-Klipper_lpc1769_0D200015871C4AAF52587C5DC52000F5-if00 btt-skr-turbo-v1.4 | ~/klipper/scripts/flash-sdcard.sh /dev/serial/by-id/usb-Klipper_lpc1769_0D200015871C4AAF52587C5DC52000F5-if00 btt-skr-turbo-v1.4 | ||
* Build for RP2040 | * Build for RP2040 | ||
make menuconfig | |||
--> rp2040 | |||
make flash FLASH_DEVICE=/dev/serial/by-id/usb-Klipper_rp2040_504450612888B91C-if00 | make flash FLASH_DEVICE=/dev/serial/by-id/usb-Klipper_rp2040_504450612888B91C-if00 | ||
sudo service klipper start | sudo service klipper start | ||
[[Category:Linux]] | [[Category:Linux]] | ||
Latest revision as of 21:05, 18 December 2025
This is my info for my Voron v2.4 build
- Generic Bigtreetech github: https://github.com/bigtreetech/
This is what I am using for hardware:
- BTT SKR 1.4 Turbo (LPC1769) SKR 1.4 Turbo Manual
- BTT EXT MOT EXT-MOT Manual
- 8MM Funssor Hot Bed Cast Alumnium MIC-6 Plate
110/220V Silicone AC heater has a built-in NTC 100K thermistor.
- BTT TFT35 V2.0 TFT35 V2.0 Manual
- BTT SB2209 USB (RP2040) EBB Manual
DC12V-DC24V 9A Temperature Sensor Interface 1x 100K NTC (pull-up resistor is 2.2K), supports PT1000
- Followed this guide to install in Debian 12
https://docs.mainsail.xyz/setup/getting-started/manual-setup
Add pkg-config to install
sudo service klipper stop
- Build for SKR 1.4 Turbo
make menuconfig --> lp1769 & 120hz make ~/klipper/scripts/flash-sdcard.sh /dev/serial/by-id/usb-Klipper_lpc1769_0D200015871C4AAF52587C5DC52000F5-if00 btt-skr-turbo-v1.4
- Build for RP2040
make menuconfig --> rp2040 make flash FLASH_DEVICE=/dev/serial/by-id/usb-Klipper_rp2040_504450612888B91C-if00
sudo service klipper start